THE INFLUENCE OF FRICTION STIR WELDED PROCESS PARAMETERS OF AA2519-T62 ON JOINT QUALITY DEFINED BY NON-DESTRUCTIVE LASER AMPLIFIED ULTRASONIC METHOD AND BY MICROSTRUCTURE ANALYSIS

Authors

  • Alexander Kravcov Czech Technical University in Prague, Faculty of Civil Engineering, Department of Construction Technology, Thákurova 7, 160 00 Prague, Czech Republic https://orcid.org/0000-0003-1551-4867
  • Robert Kosturek Military University of Technology, Faculty of Mechanical Engineering, Institute of Robots & Machine Design, gen. S. Kaliskiego Street 2, Warsaw, 00-908, Poland
  • Lucjan Śnieżek Military University of Technology, Faculty of Mechanical Engineering, Institute of Robots & Machine Design, gen. S. Kaliskiego Street 2, Warsaw, 00-908, Poland https://orcid.org/0000-0002-1157-0565
  • Janusz Kluczyński Military University of Technology, Faculty of Mechanical Engineering, Institute of Robots & Machine Design, gen. S. Kaliskiego Street 2, Warsaw, 00-908, Poland https://orcid.org/0000-0002-6058-965X
  • Ondřej Franek Czech Technical University in Prague, Faculty of Civil Engineering, Department of Construction Technology, Thákurova 7, 160 00 Prague, Czech Republic https://orcid.org/0000-0002-7248-5452
  • Nikolaj Morozov Czech Technical University in Prague, Faculty of Civil Engineering, Department of Construction Technology, Thákurova 7, 160 00 Prague, Czech Republic
  • Pawel Maciejewski War Studies University, Management and Command Faculty, gen. Antoniego Chrusciela "Montera" Street 103, Warsaw, 00-910, Poland

DOI:

https://doi.org/10.14311/AP.2020.60.0415

Keywords:

Friction Stir Welding, aluminum alloys, microstructure analysis, laser ultrasonic structuroscopy, non-destructive testing

Abstract

The presented research contains a description of a non-destructive laser ultrasound internal structure analysis of aluminium joints made by friction stir welding. In the research, four selected technological parameter groups were taken into account. Modifications used in different parameter groups included changing tool traverse speeds and also its rotation speeds. The most important goal of this research was to determine the joint quality using a non-destructive laser amplified ultrasound method  To verify obtained test results, an additional microstructural analysis was also conducted.

Downloads

Download data is not yet available.

References

MISHRA, R.S.; MAHONEY, M.W., Friction Stir Welding and Processing; ASM International: Materials Park, OH, USA, 2007; ISBN 978-0-87170-840-3.

RAO, C.V., REDDY, G.M., RAO, K.S., Microstructure and pitting corrosion resistance of AA2219 Al-Cu alloy friction stir welds - Effect of tool profile. Def. Technol. 2015, 11, 123-131.

https://doi.org/10.1016/j.dt.2014.10.003

BABU, S.; ELANGOVAN, K.; BALASUBRAMANIAN, V., Optimizing friction stir welding parameters to maximize tensile strength of AA2219 aluminium alloy joints. Met. Mater. Int. 2009, 15, 321-330.

https://doi.org/10.1007/s12540-009-0321-3

SABARI, S.S.; MALARVIZHI, S.; BALASUBRAMANIAN, V., Characteristics of FSW and UWFSW joints of AA2519-T87 aluminium alloy: Effect of tool rotation speed. J. Manuf. Process. 2016, 22, 278-289.

https://doi.org/10.1016/j.jmapro.2016.03.014

KOSTUREK, R.; WACHOWSKI, M.; ŚLĘZAK, T.; ŚNIEŻEK, L.; MIERZYŃSKI, J.; SOBCZAK, U., Research on the friction stir welding of Titanium Grade 1. In Proceedings of the International Conference on Advanced Functional Materials and Composites (ICAFMC2018), MATEC Web of Conferences 242, Barcelona, Spain, 5-6 September 2018.

https://doi.org/10.1051/matecconf/201824201006

ZHANG, Z.; XIAO, B.L.; MA, Z.Y., Effect of welding parameters on microstructure and mechanical properties of friction stir welded 2219Al-T6 joints. J. Mater. Sci. 2012, 47, 4075-4086.

https://doi.org/10.1007/s10853-012-6261-1

LIANG, X.P.; LI, H.Z.; LI, Z.; HONG, T.; MA, B.; LIU, S.D.; LIU, Y., Study on the microstructure in a friction stir welded 2519-T87 Al alloy. Mater. Des. 2012, 35, 603-608.

https://doi.org/10.1016/j.matdes.2011.10.009

FISHER, J., JAMES, J., Aluminum alloy 2519 in military vehicles. Mater. Sci. Forum 2002, 160, 43-46.

WU, Y.P., YE, L.Y., JIA, Y., LIU, L., ZHANG, X.M., Precipitation kinetics of 2519A aluminum alloy based on aging curves and DSC analysis. Trans. Nonferrous Metal. Soc. China 2014, 24, 3076-3083.

https://doi.org/10.1016/S1003-6326(14)63445-2

SCHAER, G.B., SERCOMBE, T.B., LUMLEY, R.N., Liquid phase sintering of aluminium alloys. Mater. Chem. Phys. 2001, 67, 85-91.

https://doi.org/10.1016/S0254-0584(00)00424-7

STOICHEV, N.V., YANEVA, S.B., REGEL, L.L., VIDENSKIY, I.V., Eutectic solidification of Al-Cu alloys influenced by convection. Adv. Space Res. 1998, 8, 171-174.

https://doi.org/10.1016/0273-1177(88)90020-8

GÜNDÜZ, M.; ÇADIRLI, E., Directional solidification of aluminium-copper alloys. Mater. Sci. Eng. A Struct. 2002, 327, 167-185.

https://doi.org/10.1016/S0921-5093(01)01649-5

XU,W.F.; LIU, J.H.; CHEN, D.L.; LUAN, G.H., Low-cycle fatigue of a friction stir welded 2219-T62 aluminium alloy at different welding parameters and cooling conditions. Int. J. Adv. Manuf. Technol. 2014, 74, 209-218.

https://doi.org/10.1007/s00170-014-5988-z

KOSTUREK, R.; ŚNIEŻEK, L.; WACHOWSKI, M.; TORZEWSKI, J., The Influence of Post-Weld Heat Treatment on the Microstructure and Fatigue Properties of Sc-Modified AA2519 Friction Stir-Welded Joint. Materials 2019, 12, 583.

https://doi.org/10.3390/ma12040583

KOSTUREK, R., ŚNIEŻEK, L., TORZEWSKI, J., WACHOWSKI, M., Research on the Friction Stir Welding of Sc-Modified AA2519 Extrusion. Metals 2019, 9, 1024.

https://doi.org/10.3390/met9101024

KOSTUREK, R., ŚNIEŻEK, L., TORZEWSKI, J., WACHOWSKI, M., Research on the friction stir welding of Sc-modified AA2519 extrusion, Metals, Volume 9, Issue 10, October 2019, Article number 1024, https://doi.org/10.3390/met9101024

STOLLER, J., ZEZULOVA, E., Use of ultrasound-The ultrasonic pulse velocity method for the diagnosis of protective structures after the load of TNT explosion, pp. 230-235 in ICMT 2017 - 6th International Conference on Military Technologies. https://doi.org/10.1109/MILTECHS.2017.7988761

SVOBODA, P., KRAVCOV, A., POSPÍCHAL, V., MOROZOV, N., ZEZULOVÁ, E., Quality assessment of bored pile foundations by a set of non-destructive testing methods, ICMT 2019 - International Conference on Military Technologies 2019. Brno https://doi.org/10.1109/MILTECHS.2019.8870062

ŠTOLLER J., DVORAK P., Ultrasound Diagnosis of Protective Structures after Contact Explosion. In: Transport Means 2014. Kaunas, Lithuania: Kaunas University of Technology, Lithuania, 2014, p. 264-267. ISSN 2351-4604

Janusz Kluczyński, Lucjan Śnieżek, Alexander Kravcov, Krzysztof Grzelak, Pavel Svoboda, Ireneusz Szachogłuchowicz, Ondřej Franek, Nikolaj Morozov, Janusz Torzewski, Petr Kubeček, The Examination of Restrained Joints Created in the Process of Multi-Material FFF Additive Manufacturing Technology, Materials 2020, 13(4), 903; https://doi.org/10.3390/ma13040903

QUINTERO R., SIMONETTI F., SELLINGER A., Noncontact laser ultrasonic inspection of Ceramic Matrix Composites (CMCs), NDT & E International 88, 8-16, 2017

https://doi.org/10.1016/j.ndteint.2017.02.008

KRAVCOV, A., SHIBAEV, I., "Examination of structural members of aerial vehicles by laser ultrasonic structuroscopy," International Journal of Civil Engineering and Technology, vol. 9, issue 11, pp. 2258-2265, November 2018.

KRAVCOV, A., PLATEK, P., POSPICHAL, V., KOPERSKI, W., Internal structure research of 3D printed cellular structures by laser-ultrasonic structuroscopy, ICMT 2019 - International Conference on Military Technologies 2019. Brno, https://doi.org/10.1109/MILTECHS.2019.8870047

Downloads

Published

2020-11-02

How to Cite

Kravcov, A., Kosturek, R., Śnieżek, L., Kluczyński, J., Franek, O., Morozov, N., & Maciejewski, P. (2020). THE INFLUENCE OF FRICTION STIR WELDED PROCESS PARAMETERS OF AA2519-T62 ON JOINT QUALITY DEFINED BY NON-DESTRUCTIVE LASER AMPLIFIED ULTRASONIC METHOD AND BY MICROSTRUCTURE ANALYSIS. Acta Polytechnica, 60(5), 415–419. https://doi.org/10.14311/AP.2020.60.0415

Issue

Vol. 60 No. 5 (2020)

Section

Articles