Investigation the plastic flows in the metal stamping-drawing process at the die corner

Authors

  • Anton V. Onopchenko National Aerospace University “Kharkiv Aviation Institute”, Faculty of Aviation Engines, Technologe of Manufacturing Aviation Engines Department, Vadyma Manka 17, 61070 Kharkiv, Ukraine
  • Maksym O. Kurin National Aerospace University “Kharkiv Aviation Institute”, Faculty of Aviation Engines, Technologe of Manufacturing Aviation Engines Department, Vadyma Manka 17, 61070 Kharkiv, Ukraine
  • Yurii V. Shyrokyi National Aerospace University “Kharkiv Aviation Institute”, Faculty of Aviation Engines, Theoretical Mechanics, Mechanical Engineering, and Robotic Systems Department, Vadyma Manka 17, 61070 Kharkiv, Ukraine
  • Oleksii O. Horbachov National Aerospace University “Kharkiv Aviation Institute”, Faculty of Aviation Engines, Technologe of Manufacturing Aviation Engines Department, Vadyma Manka 17, 61070 Kharkiv, Ukraine

DOI:

https://doi.org/10.14311/AP.2024.64.0385

Keywords:

sheet metal stamping-drawing, plastic flows, modelling, deformation intensity, stress intensity, process power parameters

Abstract

The present investigation covers the study of the influence of metal-plastic flow on the die corner for the deformed state of the blank and energy-power parameters during stamping-drawing. The influence of workpiece size and material on stress intensity and maximum deformation force has also been investigated both experimentally and theoretically. In addition, simulation of the stamping and drawing process was also presented. One type of die, with variations in diameter are considered different in the drawn part size and for each standard size four types of workpiece materials have been considered. The stamping process continued until the part failed structurally. The predicted test results show a dependence of the maximum load and stress intensity on both the diameter of the blank and the yield strength of the alloys and these data are in agreement with the actual measured values. Then, the method for calculating the processes of plastic deformation of metals based on a closed set of equations of continuum mechanics is proposed for the theoretical study of energy-power parameters of the technological processes. Comparison of the results of a full-scale experiment, simulation of metal flow at the die corner and theoretical calculations shows that the proposed theoretical model gives satisfactory results and can be effectively used for engineering calculations.

Downloads

Download data is not yet available.

References

P. J. Arrazola, T. Özel, D. Umbrello, et al. Recent advances in modelling of metal machining processes. CIRP Annals 62(2):695–718, 2013. https://doi.org/10.1016/j.cirp.2013.05.006

S. Melkote, S. Liang, T. Özel, et al. 100th anniversary issue of the manufacturing engineering division paper. A review of advances in modeling of conventional machining processes: From merchant to the present. Journal of Manufacturing Science and Engineering 144(11):110801, 2022. https://doi.org/10.1115/1.4053522

B. Bahrami, S. Ghouli, M. Nejati, et al. Size effect in true mode II fracturing of rocks: Theory and experiment. European Journal of Mechanics – A/Solids 94:104593, 2022. https://doi.org/10.1016/j.euromechsol.2022.104593

T. Pepelnjak, L. Sevšek, O. Lužanin, M. Milutinović. Finite element simplifications and simulation reliability in single point incremental forming. Materials 15(10):3707, 2022. https://doi.org/10.3390/ma15103707

A. Graça, G. Vincze. A short review on the finite element method for asymmetric rolling processes. Metals 11(5):762, 2021. https://doi.org/10.3390/met11050762

R. Chitchyan, C. Bird. Theory as a source of software and system requirements. Requirements Engineering 27(3):375–398, 2022. https://doi.org/10.1007/s00766-022-00380-w

G. Martynenko, N. Smetankina, V. Martynenko, et al. Simulation modelling of the process of birds fly into the turbojet aircraft engine fan to determine most dangerous cases in terms of blade strength. In 2022 IEEE 3rd KhPI Week on Advanced Technology (KhPIWeek), pp. 1–6. 2022. https://doi.org/10.1109/KhPIWeek57572.2022.9916474

A. Korchagin, Y. Deniskin, I. Pocebneva, O. Vasilyeva. Lean maintenance 4.0: Implementation for aviation industry. In Transportation Research Procedia, vol. 63, pp. 1521–1533. 2022. https://doi.org/10.1016/j.trpro.2022.06.164

T. Dolgova, D. Durov, A. Smolyaninov, N. Linkov. Design forming tooling for manufacturing parts from sheet blanks using digital technologies. E3S Web of Conferences 376:01095, 2023. https://doi.org/10.1051/e3sconf/202337601095

V. V. Chigirinsky, Y. S. Kresanov, I. Y. Volokitina. Study of kinematic and deformation parameters of rolling of compressor blade workpieces. Metallofizika i Noveishie Tekhnologii 45(5):631–646, 2023. https://doi.org/10.15407/mfint.45.05.0631

V. Deepak, O. Abhilash, Y. P. Ravitej, et al. Design and development of progressive tool for mold tag. In AIP Conference Proceedings, vol. 2316, p. 030015. 2021. https://doi.org/10.1063/5.0038385

H. Kim, J. H. Sung, R. Sivakumar, T. Altan. Evaluation of stamping lubricants using the deep drawing test. International Journal of Machine Tools and Manufacture 47(14):2120–2132, 2007. https://doi.org/10.1016/j.ijmachtools.2007.04.014

E. Evin, N. Daneshjo, A. Mareš, et al. Experimental assessment of friction coefficient in deep drawing and its verification by numerical simulation. Applied Sciences 11(6):2756, 2021. https://doi.org/10.3390/app11062756

M. P. Pereira, M. Weiss, B. F. Rolfe, T. B. Hilditch. The effect of the die radius profile accuracy on wear in sheet metal stamping. International Journal of Machine Tools and Manufacture 66:44–53, 2013. https://doi.org/10.1016/j.ijmachtools.2012.11.001

K. Bouchaâla, M. F. Ghanameh, M. Faqir, et al. Numerical investigation of the effect of punch corner radius and die shoulder radius on the flange earrings for AA1050 and AA1100 aluminum alloys in cylindrical deep drawing process. Heliyon 7(4):e06662, 2021. https://doi.org/10.1016/j.heliyon.2021.e06662

V. M. Brathikan, S. Jayabalu, S. G. Devairakkam, et al. Effect on the product finish in deep drawing process due to supremacy of punch force. In Journal of Physics: Conference Series, vol. 2272, p. 012015. IOP Publishing, 2022. https://doi.org/10.1088/1742-6596/2272/1/012015

O. Ozdilli, M. E. Erdin. Comparison of common deep drawing steel sheets in terms of blank holder force and friction conditions. International Journal of Automotive Science And Technology 2(3):36–41, 2018. https://doi.org/10.30939/ijastech..463629

H. Zein, M. El-Sherbiny, M. Abd-Rabou, M. El-Shazly. Effect of die design parameters on thinning of sheet metal in the deep drawing process. American Journal of Mechanical Engineering 1(2):20–29, 2013. https://doi.org/10.12691/ajme-1-2-1

V. M. Brathikan, N. Sangeetha, B. Sangeethkumar, K. Scidarth. Influence of various blank diameter in deep drawing. In Materials Today: Proceedings, vol. 68, pp. 1995–1999. 2022. https://doi.org/10.1016/j.matpr.2022.08.281

V. Savas, O. Secgin. A new type of deep drawing die design and experimental results. Materials & Design 28(4):1330–1333, 2007. https://doi.org/10.1016/j.matdes.2006.01.004

P. D. Gogawale, N. Bagal, B. Kedar. Calculation of deep drawing force in CR4 metal forming. International Journal of Advanced Research in Science & Technology 8(3):44–50, 2020. [2024-05-22]. https://ijarsct.co.in/Paper276.pdf

R. Arhat, R. Puzyr, V. Shchetynin, et al. The stress state of the workpiece at the radius of matrix rounding during drawing, considering the bending moment. In V. Tonkonogyi, V. Ivanov, J. Trojanowska, et al. (eds.), Advanced Manufacturing Processes III, pp. 479–488. Springer International Publishing, Cham, 2022. https://doi.org/10.1007/978-3-030-91327-4_47

M. Thor, M. G. R. Sause, R. M. Hinterhölzl. Mechanisms of origin and classification of out-of-plane fiber waviness in composite materials – A review. Journal of Composites Science 4(3):130, 2020. https://doi.org/10.3390/jcs4030130

H. Blala, L. Lang, S. Khan, S. Alexandrov. Experimental and numerical investigation of fiber metal laminate forming behavior using a variable blank holder force. Production Engineering 14(4):509–522, 2020. https://doi.org/10.1007/s11740-020-00974-9

S. M. Hussaini, G. Krishna, A. K. Gupta, S. K. Singh. Development of experimental and theoretical forming limit diagrams for warm forming of austenitic stainless steel 316. Journal of Manufacturing Processes 18:151–158, 2015. https://doi.org/10.1016/j.jmapro.2015.03.005

H. Zein, O. M. Irfan. Optimization and mapping of the deep drawing force considering friction combination. Applied Sciences 11(19):9235, 2021. https://doi.org/10.3390/app11199235

Livermore software technology corporation. LS-DYNA® Keyword user’s manual. Volume I, 2007. [2024-05-22]. https://www.academia.edu/40555890/LS_DYNA_KEYWORD_USERS_MANUAL_VOLUME_I

ansys.com. Ansys Granta: Materials information management. [2024-05-22]. https://www.ansys.com/products/materials

V. Prakash, D. Ravi Kumar. Numerical simulation of warm deep drawing incorporating strain rate effect in sheet material properties. In Materials Today: Proceedings, vol. 18, pp. 2595–2602. 2019. https://doi.org/10.1016/j.matpr.2019.07.118

V. Prakash, R. K. Digavalli, M. Lenzen, et al. Numerical simulation of sheet metal forming of an Al-Mg alloy incorporating plane strain properties in the yield criterion. Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture 238(3):373–384, 2024. https://doi.org/10.1177/09544054221135388

J. Domitner, Z. Silvayeh, A. Shafiee Sabet, et al. Characterization of wear and friction between tool steel and aluminum alloys in sheet forming at room temperature. Journal of Manufacturing Processes 64:774–784, 2021. https://doi.org/10.1016/j.jmapro.2021.02.007

A. Gontarz, A. Dziubińska, Ł. Okoń. Determination of friction coefficients at elevated temperatures for some Al, Mg and Ti alloys. Archives of Metallurgy and Materials 56(2):379–384, 2011. https://doi.org/10.2478/v10172-011-0040-x

M. D. Sharma, R. Sehgal. Dry sliding friction and wear behaviour of titanium alloy (Ti-6Al-4V). Tribology Online 7(2):87–95, 2012. https://doi.org/10.2474/trol.7.87

J. Adamus, P. Lacki, M. Motyka, K. Kubiak. Investigation of sheet-titanium drawability. In Proceedings of the 12th World Conference on Titanium, pp. 337–340. 2012.

A. Onopchenko, O. Horbachov, V. Sorokin, et al. Optimal conditions for deformation of stamping-drawing process from aviation materials. In V. Tonkonogyi, V. Ivanov, J. Trojanowska, et al. (eds.), Advanced Manufacturing Processes IV, pp. 109–118. Springer International Publishing, Cham, Germany, 2023. https://doi.org/10.1007/978-3-031-16651-8_11

M. O. Kurin. Analysis the process of plastic deformation metal chip at non-free cutting. Metallofizika i Noveishie Tekhnologii 42(3):433–449, 2020. https://doi.org/10.15407/mfint.42.03.0433

Y. P. Korkolis, B. R. Mitchell, M. R. Locke, B. L. Kinsey. Plastic flow and anisotropy of a lowcarbon steel over a range of strain-rates. International Journal of Impact Engineering 121:157–171, 2018. https://doi.org/10.1016/j.ijimpeng.2018.07.015

D. Sánchez-Ávila, R. Barea, E. Martínez, et al. Determination of the instantaneous strain rate during small punch testing of 316L stainless steel. International Journal of Mechanical Sciences 149:93–100, 2018. https://doi.org/10.1016/j.ijmecsci.2018.09.042

T.-T. Luyen, V.-C. Tong, D.-T. Nguyen. A simulation and experimental study on the deep drawing process of SPCC sheet using the graphical method. Alexandria Engineering Journal 61(3):2472–2483, 2022. https://doi.org/10.1016/j.aej.2021.07.009

A. Singh, S. Basak, P. S. Lin Prakash, et al. Prediction of earing defect and deep drawing behavior of commercially pure titanium sheets using CPB06 anisotropy yield theory. Journal of Manufacturing Processes 33:256–267, 2018. https://doi.org/10.1016/j.jmapro.2018.05.003

M. Mahmoud, F. Bay, D. P. Muñoz. An efficient multiphysics solid shell based finite element approach for modeling thin sheet metal forming processes. Finite Elements in Analysis and Design 198:103645, 2022. https://doi.org/10.1016/j.finel.2021.103645

R. K. Lal, V. K. Choubey, J. P. Dwivedi, S. Kumar. Study of factors affecting springback in sheet metal forming and deep drawing process. In Materials Today: Proceedings, vol. 5, 2, pp. 4353–4358. 2018. https://doi.org/10.1016/j.matpr.2017.12.002

N. Fang, I. S. Jawahir. Analytical predictions and experimental validation of cutting force ratio, chip thickness, and chip back-flow angle in restricted contact machining using the universal slip-line model. International Journal of Machine Tools and Manufacture 42(6):681–694, 2002. https://doi.org/10.1016/S0890-6955(02)00006-8

D. Sornette, A. B. Davis, K. Ide, et al. Algorithm for model validation: Theory and applications. In Proceedings of the National Academy of Sciences, vol. 104, 16, pp. 6562–6567. 2007. https://doi.org/10.1073/pnas.0611677104

Downloads

Published

2024-09-08

Issue

Section

Articles

How to Cite

Onopchenko, A. V., Kurin, M. O., Shyrokyi, Y. V. ., & Horbachov, O. O. . (2024). Investigation the plastic flows in the metal stamping-drawing process at the die corner. Acta Polytechnica, 64(4), 385-397. https://doi.org/10.14311/AP.2024.64.0385