Numerical study on the TBM mucking performance in EH project and optimization of the supporting ribs
DOI:
https://doi.org/10.14311/CEJ.2025.02.0016Keywords:
TBM, Muck transfer, discrete element method, EDEM, supporting ribAbstract
To study the cutterhead’s muck transfer performance of the TBM applied in EH project, China, a discrete element method (DEM) based numerical model was built and the mucking process was simulated at different penetration rates and cutterhead rotational speed. It is found that the conventional straight-supporting-rib cutterhead performed well at different penetration rates and low RPMs, but the muck excessive-thrown problem was serious when the RPM was higher than 10 rev/min. To overcome this problem, a new arched-supporting-rib cutterhead was proposed. The curvature radius of the arched supporting ribs is suggested between 1.25 m and 1.75 m, and the offset angle is suggested between 40° and 45°. The newly proposed arched-supporting-rib cutterhead can performed well in muck transfer at a greater RPM range of 4~13 rev/min, which allow the TBM to excavated at low, medium and high RPMs considering ground conditions and requirement of construction progress.
Downloads
References
. Qi M.X., Wang Y.J., Li H.L., et al., 2009. Research and application of overall refit of open type TBM. Modern Tunnelling Technology, vol. 46(04): 64-70.
. MAO B.Q., 2013, Improvement of the tool and scraper system for TBM under abnormal geological conditions. Construction Machinery ,vol. (11): 99-102+107.
. Zhang J, 2019, Production of TBM ballast scraper using low alloy wear resistant cast steel. Building Technique Development, vol. 46(04): 54-55.
. Geng Q, Zhang H, Liu X, et al., 2019. Numerical study on the rock muck transfer process of TBM cutterhead with clump strategy based on discrete element method. Tunnelling and Underground Space Technology, vol. 91
. Geng Q, Xie L.Y., Zhang Z.Y., et al., 2020. Influence of tunnel boring machine scraper bucket structure on the mucking performance. Journal of Xi'an Jiaotong University, vol. 54(11): 149-157.
. Geng Q, Zhang X.Y., Zhang Z.Y., et al., 2023. A numerical simulation study on the mucking mechanism of tbm two-stage spiral cutterhead. Modern Tunnelling Technology, vol. 60(02): 1-10.
. Zhang X.Y., 2023. Research on ballast discharging mechanism and performance of opposite-type cutter of full-section rock tunnel boring machine. Xi’an: Chang’an University.
. Xia Y.M., Yang M., Wu D., et al., 2018. Influence of the TBM mucking slots structure on the discharge characteristics of ballasts. Journal of Harbin Engineering University, vol. 39(9): 1561-1567.
. Xia Y.M., Yang M., Lin L.K., et al., 2021. Effect of blade angles on the shovel muck capacity and wear characteristics for TBM scraper. Arabian Journal for Science and Engineering, vol. 46(5): 5203-5218.
. Xia Y.M., Yang M., Mei Y.B., et al., 2022. Influence of geological properties and operational parameters on TBM muck removal performance for yinsong tunnel. Geotechnical and Geological Engineering, vol. 40(4): 2291-2306.
. Yang M., Xia Y.M., Lin L.K., et al. ,2020. Optimal design for buckets layout based on muck removal analysis of TBM cutterhead. Journal of Central South University, vol. 27(6): 1729-1741.
. Yang M., Xia Y.M., et al., 2017. Comprehensive performance evaluation method of mucking structure for TBM cutterhead//International Conference on Tunnel Boring Machines in Difficult Grounds. Wuhan: TBM DiGs, vol. : 1-14.
. Huo J.Z., Chen W., OuYang X.Y., et al., 2015. Optimum design of TBM mucking slot based on the rock ballasts fluidity. Journal of Northeastern University(Natural Science), vol. 36(5): 715-718.
. Chen W., 2015. TBM mucking process simulation based on discrete element method and a new mucking structure design. Dalian: Dalian University of Technology.
. Chen W., Sun W., Huo J.Z.,et al., 2015. The open area determination of TBM cutterhead. Machinery Design & Manufacture, vol. (5): 29-31+35.
. Nie X.D., Hu J., Nie S.W., et al., 2018. Optimization method for structural design of mucking plate. Chinese Journal of Construction Machinery, vol. 16(5): 421-426.
. Li D.P.,et al., 2013. Process simulation of the TBM knife disc slip to be based on abaqus. Construction Machinery Technology & Management, vol. 26(6): 101-106.
Downloads
Published
Issue
Section
License
Copyright (c) 2025 Author
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
Authors who publish with this journal agree to the following terms:
- Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
- Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.
- Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work (See The Effect of Open Access).
